| Vanagon & Bus Parts |
|
| Vanagon & Bus Parts |
|
VANAGON / BUS NEW & USED PARTS
|
Here's a brand new custom made Vanagon front heater core that has been not available anywhere for some time --not at VW, Not at an Auto Parts Store.
The part is No Longer Available.
These cores are a big improvement from the stock core are designed and devloped by me.
The have a larger core tubes, and flow more air over them offering bigger BTU's in the cab of the Vanagon .
They have copper cores, and steel tanks for a longer lasting, trouble free performance.
It's a neat update for your worn out front heater box & core.
$289.00 plus shipping
The Firewall Fuel Fittings are an exact drop in replacement for the original stock, fragile, plastic fitting you have on your firewall right now.
They are old, they are brittle, and they will crack, blowing gas all over the engine compartment or behind the firewall , leaking gas onto the trans. & ground.
Not a savory thought.
I had a machine shop duplicate the mounting plates using a lazer, and are an exact fit.
The tubing I bend , put the rolled beaded ends on the heavy wall tubing to hold onto the fuel hose --exactly as the original did---
It's a bullet proof solution and a final answer to get the gas to the engine without worrying that the firewall fitting is gonna fracture & leak.
It's an excellent update, and real simple to install--for any year or model Vanagon.
The HD fitting is $39.00 plus shipping.
Here is a perfect set of Genuine VW issue Vanagon rear hatch window jail bars--all polished up and ready to mount.
These bars are original VW issue and not the cheap, chessey, made in Taiwan look alike's offered by the other accessory parts vendor's.
They look real nice in the back window of any Vanagon, and give it the original Deutschland appearance.
To buy these vintage bars & mounts today through VW, it would cost you $239.00 plus tax.
This perfect set is $189.00 plus shipping.
As you can see the Bars & their mounts are in perfect shape, and are as new.
They have the original VW part number's cast in them---
They are a real neat, unique and Rare Vanagon accessory.
A set of new stainless mounting screws are included .
Here's a replacement Vanagon Westfala Stove Cover & drain board.
It's straight, it's clean, and it isn't all purple from somebody trying to cook pancakes on it--
Canadian Vanagon Westfalia's didn't have this option installed when they were new--
$84.00 plus shipping
Here's a real nice & clean Westfalia Stove Vent assembly.
Comes complete with the baffles & soft & supple body mount gasket.
It looks as good as new--
$39.00 plus shipping
Here is a vintage VW Vanagon or Bus, Bon Aire floor mounted DELUXE swamp cooler in perfect operating condition.
It's has a 12 volt blower inside of it--fill it with ice and water, and it recirculates cool air inside your Van or Bus.
It isn't like the window mounted units that always are intaking hot air, and trying to cool it down before it gets inside the vehicle.
This swamp cooler constantly recirculates the cool air that it's making inside your Bus or Vanagon
This unit also has a can or bottle cooler built into the top of it that will cool down two beverages of your choice.
It also has a built in bottle opener on the side of it.
It has two cup holder's built into the top of it, a map pocket ithe front of it, and a water level indicator.
This is a neat optional Vintage VW accessory out of the past that looks and works perfect---
It comes in the origianl Bon Aire box with the orginal instructions, parts, & warrantee card inclueded !
$350.00 plus shipping
Here you can see the beverage door open--ready to cool down a couple of brew's.
One Brand new pair of front door window vent shades--
You can leave your front door window's cracked oped in the rain, to get fresh air into your Van with the Vent shades mounted onto the door.
$54.00 plus shipping
Here's a new accessory that will give your 83.5 to 85 1.9 or 86 to 91 2.1 Vanagon a hand starting durring the cold winter months.
It connects into the coolant line, and when plugged in while the engine is hot---it'll keep the coolant warm all night long.
Fast, Easy Winter Starting--Fast Heat.
Easy Installation instructions, plus the hose clamps to mount the heater are included.
$32.95 plus shipping
Ever tried to hook up any trailer lights to your Vanagon and found that the trailer lights won't work?
Here is what you need to get the lamps on the trailer to function;
A European tail lamp to US trailer tail lamp conversion kit.
It's a brand new kit-- and comes complete with installation instructions.
$33.95 plus shipping.
I'm rebuilding rear axle housings.
Send me your big miled, no maintainece, housing & axle , and I send you back a rebuilt one, with new inner and outer bearings, inner and outer seals installed, the bearings are repacked with high pressure, high temp grease, and I drill,and install a zerk fitting into the housing so you can easily periodicly grease the rear axle bearings.
The price is $275.87 per rebuilt axle assembly exchange only.
If your hubs / axles are destroyed, or you don't have a core, add $100.00 per axle housing to the price for the core charge.
Or you can stop in at any VW dealer and order up a new axle assembly for $587.60, plus tax-- with no zerk fitting installed.
One Brand New pair of Automatic Trans rear axle seals---
$ 43.70 for the pair
Here's a custom made steel bleeder loop, to replace the dried up,& fractured plastic or rusted out one you now have on yor Van.
It's an exact duplicate of the original---& replaces the No Longer Available, broken, leaking loop
in your Vanagon,
This is another VW Vanagon part that I custom manufacture & is only available here---
It fits all 83.5 to 91 water cooled Vanagons.
$169.00 plus shipping.
Here's the lower "H" pipe to coolant pipe
replacement hose--custom built.
These pipes for the 1.9 are also No Longer Available from VW.
The VW hose pt. number is;
025-121-062-C
This hose is for the later model 1.9's with the 1.50" coolant hose running to the radiator.
All the clamps & fittings to fit are included.
$112.00 plus shipping
Here's a custom built replacement coolant return hose to the Thermostat housing for any Automatic trans Vanagon.
The original VW part number is;
025-121-062-F
The hose is no longer available from VW.
I developed these replacement hoses & manufacture them especially for Vanagons, & they fit perfect!
All the clamps, hoses & stainless pipe are included.
$159.00 plus shipping.
The duplicate I manufacture is on the bottom.
It's a perfect match and fits just as the stock hose did--
Brand New VW Diesel Vanagon engine to radiator & oil cooler hose.
Pt.# 068-121-101-H
$320.75 plus shipping
Brand new coolant distribution block.
VW part #251-121-438-B $58.30 plus priority mail shipping.
This hose runs from the coolant expansion tank to the water pump.
It's a brand new hose.
VW parts # 025-121-108-D
$19.25 plus shipping
Brand spanking new R/H head to coolant distribution block hose.
VW parts # 251-121-130-B
$19.25 plus shipping
One perfectly in good shape late model lower thermostat hose--used
$3.50 plus shipping
This is a brand new, never clamped to anything, still in the VW parts wrapper, automatic trans cooler hose.VW parts # 025-121-104-D
for any 86 to 91 Vanagon.
$33.95 plus shipping
Here's one perfect replacement water pump feed pipe to the the right hand head .
It has no rust, corrosion, inside or out, and comes complete with a new, genunine VW hose union & stainless aircraft hose clamps.
$89.00 plus shipping.
Here's an item that you'll often find rusted out and broken.
It's the hose holder on top of the trans that keeps the two main hoses that go to the coolant tubes from rubbing on the top of the trans.
It's in real nice shape.
$12.00 plus shipping
One Brand New pair of Genuine VW Issue side marker lamp lenes for any 80 to 9
1 Vanagon.
These are not the Made in Taiwan look alikes available at most of any of the other on line parts distributor's---
If your looking for genuine lenes that will stay red, and not fade out in 6 months, these are what you need.
$58.70 for the pair, plus Priority Mail shipping.
LIst at VW is $65.00, plus tax for the pair.
Here is a brand new side marker light wiring harness & socket assembly.
It's the only way to replace your rusted out and corroded socket--because it's the only way it's available.
Replace the whole set up and your Van's side marker lights will be good for another 20 years.
$49.70 plus priority mail shipping.
One full set of nylon mounting nuts, & screws to replace the dried up and spinning lens mounts on your van.
$9.80 plus shipping
One Time / Warning Relay ( chime ) for any 85 to 91 Vanagon.
It mounts right into the fuse panel
$39.00 plus priority mail shipping.
These things retail for $73.52 at VW----
Excellent front windshield wiper motor--in perfect shape, for any 80 to 91 Vanagon $49.00 plus shipping
This is the temperature sensor that regulates the compressor's running time , and the temp of the cold air blowing inside your Van--
$ 28.00, plus shipping.
Here is the low side pipe that bolts to the back side of your compressor--it's usually all rusted out and leaking--
This is where the AC system gets charged at this point in the AC system.
This one is clean, and for any 86 to 91 Vanagon
$69.00 plus shipping.
This pipe retails for $149.73 at VW---
Here's one real nice & totally operational rear AC motor & fan assembly---
$64.70 plus shipping.
Here's brand new rear Air conditioner 3 speed ceramic resistor's.
If your AC won't run on all 3 speed's this is probably the reason---
$54.30 each plus shipping.
Here's a rear AC & Radiator Fan Relay mount, bus bar & relay, for any 86 to 91 Vanagon--in real nice shape.
$29.00 plus shipping
Here's a complete rear AC relay assembly--with the bus bar for any 86 to 91 Vanagon.
$45.00 plus shipping.
Ever wonder what type of mounting snaps are on that front curtain of the Wolfsburg or Carat ?
Here they are, brand new, genuine VW issue.
$9.00 for the pair plus shipping.
Two white, one R'H front doors off a 90 Carat and a 87 Maroon GL---no bangs-- no dents--no rust---complete with glass---no mirrors, or interior door panels--$145.00 each--
Here's the rear fresh air intake louver's for any 80 to 91 Vanagon.
They're Clean as new, the screw holes are perfect, and the two locating pins are perfect--nothing busted, or cracked.
I have both the left hand & right hand louver's
$19.00 each plus shipping
Is the sliding door on your Vanagon dragging, grinding on the way open and closed, not closing or opening right?
The roller bearings & guide roller bearing are suffering from petrolis neglectus, and seizing up.
There is no way to lubricate them, as they are sealed bearings and just worn out from age.
Here is a totally rebuilt rear hinge assemebly, with the roller bearings replaced, the guide roller replaced, the circlips, piviot spacer's and collars replaced, even the has a new door weather strip included, the piviot pins dissassembled, cleaned and regreased with high temp / high pressure grease.
The hinge / roller assembly is as good if not better than new.
The assembly is now NLA from VW and if you could get it the price is $537.00
The parts to rebuild the hinge cost $219.00 and some change.
The rebuilt unit, ready to install is $257.60, exchange , plus shipping.
I need / require your old worn out hinge assembly and is not included along with the cost of the hinge.
It's an exchange price only.
Have No Core?
Add $75.00 for the core charge.
If your finding your Van is stalling, having off idle
problems, and are pretty sure you have TPS problems, it may not be the Throttlle Postioning switch itself.
It has a cam with operates it, makes it open and close at the right time, so the ECU has the right information of when to have the engine at full or no fuel.
This plasic cam operates the TPS.
It is a wear item--How many times does the TPS open and close durring one day?
Anyway--here is a new TPS operating cam , and the required retaining clip to hold it to the throttle shaft.
Prior to changing the Throttle Postioning Switch itself, I'd change the plastic cam first--it most likely is your problem.
$9.65 for both--plus shipping.
One brand new Vanagon Throttle return Spring.
$8.69 plus shipping.
This heated element fits into the oil breather hose that connects to the bellows between the AFM and the throttle body .
It's in perfect shape.
$15.00 plus shipping
Here's a perfect oil vent tube that runs from the breather tower to the oil vent heating element--
If your's is a little soft, & spongey--it's time to replace it.
$15.89 plus shipping.
I have a few brand new Bosch fuel pumps in stock---
Why buy a used one and wonder if it's gonna work--or how long it's gonna last?
Do the job once and be done with it for another 200,000 miles.
$198.00 plus shipping
If your Van is having a hard time
idling right, It very well could be the charcoal cannister is saturated.
They should be changed every 100,000 miles or so--weather they need it or not.
$ 55.60 plus shipping.
(Update on cannister;
They have now been moved into the VW obsolete parts list and when the current stock is depleted , there will be no more.
If you have a leaking , saturated , junk charcoal cannister, and your idle is wandering all over the place, it would be a real good time to make a move and replace it.When these ar all gone they will be history, and I have no idea how you'll get your gas emissions recovery system woking right--you'll be screwed & tattooed big time)
This is what that purple plastic hose connects to ,
and controls when and when not the vacuum draws off the charcoal cannister.
It's brand new.
If you engine has an off idle problem it may very well be this valve causing the hickup's--
$58.85 plus shipping
I know my Vanagons air cleaner's wouldn't stay
put---the mount rubber grommets that hold them in place dry rot and shrink, or got oil soaked and the air cleaner wouldn'f stay put.
Here's the answer--two new grommets.
Pop the old one's out--slip the new one's in.
Your done--and so is the Bouncing Betty air cleaner assembly.
$6.50 a pair plus shipping.
Here'a a brand new oil fill tube to replace the rusted out or bent one , complete with the black plastic telescoping extension.
These are No Longer Available from VW and I have two left in stock.
$ 86.93 plus shipping
Like new-and perfect---
$49.80 plus shipping
Perfect early model rear muffler support rod that fits in the center of the upper hanger.
$29.80 plus shipping
Perfect early Vanagon rear muffler support rod that goes to the front of the hanger.
$20.90 plus shipping
One perfect L/H exhaust pipe support rod.
$29.70 plus shipping
Need to do some welding on a busted up muffler, Tail Pipe or Converter?
Wanna build your own muffler?
Here's new in the box flanges to fit.
And they are the hot set up for connecting the exhaust parts , because they don't have threaded holes--they are bolted together with a nut and a bolt--no locked up fastener's in the threaded flanges.
$15.95 ea, plus shipping.
Here's what's possible with a new set of exhaust flanges.
This converter had rusted out ends, and a new set of flanges were welded on.
It's a s good as new again, and ready to go another 100,000 miles.
The flanges are also good for the muffler & tail pipe end replacement.
The original flanges were shot--the new flanges will give you another 100,000 miles outa the converter.
The pssibilities are endless on how you can se the new flanges.
Just weld them onto whatever you want to install
Here's a perfect Vanagon replacement Power Steering Pump Pulley---
$13.25 plus shipping.
One perfect set of 2.1 Rocker Arm Assemblies.
$60.00 for the pair plus shipping.
One brand new Vanagon Allen Head Upper Starter Bolt to replace the stripped out allen headed bolt that you rounded out in the process of removal.
It comes complete with the nut--
$8.70 plus shipping.
Ordering Info;
If you see the parts posted--they are available. Pal Pal is welcome here. Use my E-Mail address all in lower case lettering over at Pay Pal; If you choose to send cash, check or money order my mailing info is; All order's are processed via E-Mail only. If you have an important question, are broke down, or need a part yesterday, you can call me at; |
|
|
| |
|
|
||
|
|
||
|
|
||
